FAQ Buying Guide
Common questions
What is the difference between a Layer 2 and a Layer 3 switch?
A Layer 2 switch forwards traffic inside a network using MAC addresses. A Layer 3 switch does that and also routes between VLANs and subnets using IP addresses, so it can replace a separate router for internal traffic. Choose Layer 3 when you need inter-VLAN routing at the access, distribution or data center leaf layer.
What is the difference between SFP, SFP+, SFP28 and QSFP+ ports?
They are port types with different speeds. SFP carries 1 Gbps, SFP+ carries 10 Gbps, SFP28 carries 25 Gbps, QSFP+ carries 40 Gbps and QSFP28 carries 100 Gbps. The port type decides which optic or cable you can plug in, so match the module to the port on your switch.
Can I use an SFP module in an SFP+ port, or an SFP+ module in an SFP port?
An SFP module usually works in an SFP+ port at 1 Gbps, but an SFP+ module does not work in an SFP-only port. Support depends on the switch model and its software, so check the model's supported-optics list before you order, or send us the switch model and part number and we will help you confirm.
What do PoE, PoE+ and UPOE mean?
PoE (IEEE 802.3af) supplies up to 15.4 W per port and PoE+ (802.3at) up to 30 W. 802.3bt supplies 60 W (Type 3) or 90 W (Type 4), and Cisco UPOE supplies up to 60 W. Higher power suits access points, cameras and phones with displays. Compare each device's draw with the switch's total PoE budget.
How do I work out how many PoE watts I need?
Add the maximum power draw of every device you plan to power, then compare the total with the switch's PoE budget. The budget is the total power available across all ports, not a per-port figure, and it depends on the power supply fitted. Leave some headroom for devices you add later.
What is a stackable switch?
A stackable switch can be linked to other switches of the same family with stacking cables or modules, so the group works as one logical switch with one management address. Stacking simplifies management and adds redundancy. Stack members usually must belong to the same platform family, so check stacking support for the exact model.
What does 1U mean for a switch?
One rack unit (1U) is 1.75 inches (44.45 mm) of vertical rack space. A 1U switch takes one unit and a 2U switch takes two. A standard 42U rack holds up to 42 units of equipment. Check the depth as well as the height, because some data center switches need a deeper rack.
What is the difference between front-to-back and back-to-front airflow?
It describes which way the fans move air through the chassis relative to the ports. Data centers arrange racks in hot and cold aisles, so the switch's airflow must match the aisle design or it will draw in warm air and run hotter. Many models are sold in both versions, so check the airflow on the product page before you order.
What is the difference between AC and DC power supplies?
AC supplies plug into standard mains power. DC supplies connect to a DC power plant, commonly 48 V in telecom sites and some data centers. The power supply must match your site's power. Many models are sold with both options, so confirm which one the listing offers.
Should I choose a fixed-port or a modular switch?
A fixed-port switch has a set number of ports and is simpler and cheaper when the requirement is known. A modular (chassis) switch takes line cards, so you can add ports and speeds later without replacing the whole switch. Choose modular when growth is uncertain and fixed when the port count is stable.
What is the difference between access, distribution and core switches?
Access switches connect end devices such as PCs, phones and access points. Distribution (aggregation) switches collect traffic from access switches and apply routing and policy. Core switches move traffic between distribution blocks at the highest speed. Smaller networks often combine distribution and core in one layer.
What is a leaf-spine network?
Leaf-spine is a data center design in which every leaf (access) switch connects to every spine switch. Any two servers are the same number of hops apart, so latency stays predictable, and you add capacity by adding leaf or spine switches. Leaf switches connect servers and spine switches connect the leaves.
What does non-blocking mean for a switch?
A non-blocking switch can forward traffic on every port at full speed at the same time, because its switching capacity is at least the combined speed of all its ports in both directions. Compare the switching capacity on the datasheet with the total port bandwidth.
What is the difference between 10GBASE-T and SFP+ for 10 Gbps?
10GBASE-T runs 10 Gbps over twisted-pair copper with RJ-45 connectors, which suits existing cabling but uses more power and adds some latency. SFP+ uses optical modules or direct attach cables, which lowers power and latency and suits short links inside a rack or longer fiber runs.